Also honor node-ip when adding the node address to the SAN list, instead
of hardcoding the autodetected IP address.
Signed-off-by: Brad Davidson <brad.davidson@rancher.com>
This changes the crictl template for issues with the socket information. It also addresses a typo in the socket address. Last it makes tweaks to configuration that aren't required or had incorrect logic.
Signed-off-by: Jamie Phillips <jamie.phillips@suse.com>
spelling
* Move registries.yaml handling out to rancher/wharfie
* Add system-default-registry support
* Add CLI support for kubelet image credential providers
Signed-off-by: Brad Davidson <brad.davidson@rancher.com>
If the port wanted by the client load balancer is in TIME_WAIT, startup
will fail. Set SO_REUSEPORT so that it can be listened on again
immediately.
The configurable Listen call wants a context, so plumb that through as
well.
Signed-off-by: Brad Davidson <brad.davidson@rancher.com>
* Always use static ports for the load-balancers
This fixes an issue where RKE2 kube-proxy daemonset pods were failing to
communicate with the apiserver when RKE2 was restarted because the
load-balancer used a different port every time it started up.
This also changes the apiserver load-balancer port to be 1 below the
supervisor port instead of 1 above it. This makes the apiserver port
consistent at 6443 across servers and agents on RKE2.
Additional fixes below were required to successfully test and use this change
on etcd-only nodes.
* Actually add lb-server-port flag to CLI
* Fix nil pointer when starting server with --disable-etcd but no --server
* Don't try to use full URI as initial load-balancer endpoint
* Fix etcd load-balancer pool updates
* Update dynamiclistener to fix cert updates on etcd-only nodes
* Handle recursive initial server URL in load balancer
* Don't run the deploy controller on etcd-only nodes
* Add functionality for etcd snapshot/restore to and from S3 compatible backends.
* Update etcd restore functionality to extract and write certificates and configs from snapshot.
Servers should always be upgraded before agents, but generally this
isn't required because things are compatible between versions. In this
case we're OK with failing closed if the user upgrades out of order, but
we should give a clearer message about what steps are required to fix
the issue.
Signed-off-by: Brad Davidson <brad.davidson@rancher.com>
Adds support for retagging images to appear to have been sourced from
one or more additional registries as they are imported from the tarball.
This is intended to support RKE2 use cases with system-default-registry
where the images need to appear to have been pulled from a registry
other than docker.io.
Signed-off-by: Brad Davidson <brad.davidson@rancher.com>
Problem:
While using ZFS on debian and K3s with docker, I am unable to get k3s working as the snapshotter value is being validated and the validation fails.
Solution:
We should not validate snapshotter value if we are using docker as it's a no-op in that case.
Signed-off-by: Waqar Ahmed <waqarahmedjoyia@live.com>
Removing the cfg.DataDir mutation in 3e4fd7b did not break anything, but
did change some paths in unwanted ways. Rather than mutating the
user-supplied command-line flags, explicitly specify the agent
subdirectory as needed.
Signed-off-by: Brad Davidson <brad.davidson@rancher.com>
This attempts to update logging statements to make them consistent
through out the code base. It also adds additional context to messages
where possible, simplifies messages, and updates level where necessary.
* cli: add --selinux flag to agent/server sub-cmds
Introduces --selinux flag to affirmatively enable SELinux in containerd.
Deprecates --disable-selinux flag which now defaults to true which
auto-detection of SELinux configuration for containerd is no longer
supported. Specifying both --selinux and --disable-selinux will result
in an error message encouraging you to pick a side.
* Update pkg/agent/containerd/containerd.go
update log warning message about enabled selinux host but disabled runtime
Co-authored-by: Brad Davidson <brad@oatmail.org>
Signed-off-by: Jacob Blain Christen <jacob@rancher.com>
In k3s today the kubernetes API and the /v1-k3s API are combined into
one http server. In rke2 we are running unmodified, non-embedded Kubernetes
and as such it is preferred to run k8s and the /v1-k3s API on different
ports. The /v1-k3s API port is called the SupervisorPort in the code.
To support this separation of ports a new shim was added on the client in
then pkg/agent/proxy package that will launch two load balancers instead
of just one load balancer. One load balancer for 6443 and the other
for 9345 (which is the supervisor port).
Brad Davidson