consul

Tree: c17baadbf8

Author	SHA1	Message	Date
freddygv	856d5a25ee	Fix text type assertion	4 years ago
R.B. Boyer	74d5df7c7a	xds: use envoy's rbac filter to handle intentions entirely within envoy (#8569 )	4 years ago
Daniel Nephin	068b43df90	Enable gofmt simplify Code changes done automatically with 'gofmt -s -w'	5 years ago
freddygv	19e3954603	Move compound service names to use ServiceName type	5 years ago
Freddy	9ed325ba8b	Enable gateways to resolve hostnames to IPv4 addresses (#7999 ) The DNS resolution will be handled by Envoy and defaults to LOGICAL_DNS. This discovery type can be overridden on a per-gateway basis with the envoy_dns_discovery_type Gateway Option. If a service contains an instance with a hostname as an address we set the Envoy cluster to use DNS as the discovery type rather than EDS. Since both mesh gateways and terminating gateways route to clusters using SNI, whenever there is a mix of hostnames and IP addresses associated with a service we use the hostname + CDS rather than the IPs + EDS. Note that we detect hostnames by attempting to parse the service instance's address as an IP. If it is not a valid IP we assume it is a hostname.	5 years ago
Kyle Havlovitz	b14696e32a	Standardize support for Tagged and BindAddresses in Ingress Gateways (#7924 ) * Standardize support for Tagged and BindAddresses in Ingress Gateways This updates the TaggedAddresses and BindAddresses behavior for Ingress to match Mesh/Terminating gateways. The `consul connect envoy` command now also allows passing an address without a port for tagged/bind addresses. * Update command/connect/envoy/envoy.go Co-authored-by: Freddy <freddygv@users.noreply.github.com> * PR comments * Check to see if address is an actual IP address * Update agent/xds/listeners.go Co-authored-by: Freddy <freddygv@users.noreply.github.com> * fix whitespace Co-authored-by: Chris Piraino <cpiraino@hashicorp.com> Co-authored-by: Freddy <freddygv@users.noreply.github.com>	5 years ago
Chris Piraino	26f92e74f6	Compute all valid DNSSANs for ingress gateways For DNSSANs we take into account the following and compute the appropriate wildcard values: - source datacenter - namespaces - alt domains	5 years ago
Freddy	c32a4f1ece	Fix up enterprise compatibility for gateways (#7813 )	5 years ago
Kyle Havlovitz	f14c54e25e	Add TLS option and DNS SAN support to ingress config xds: Only set TLS context for ingress listener when requested	5 years ago
Kyle Havlovitz	711d1389aa	Support multiple listeners referencing the same service in gateway definitions	5 years ago
Kyle Havlovitz	247f9eaf13	Allow ingress gateways to route traffic based on Host header This commit adds the necessary changes to allow an ingress gateway to route traffic from a single defined port to multiple different upstream services in the Consul mesh. To do this, we now require all HTTP requests coming into the ingress gateway to specify a Host header that matches "<service-name>.*" in order to correctly route traffic to the correct service. - Differentiate multiple listener's route names by port - Adds a case in xds for allowing default discovery chains to create a route configuration when on an ingress gateway. This allows default services to easily use host header routing - ingress-gateways have a single route config for each listener that utilizes domain matching to route to different services.	5 years ago
Freddy	137a2c32c6	TLS Origination for Terminating Gateways (#7671 )	5 years ago
freddygv	034d7d83d4	Fix snapshot IsEmpty	5 years ago
Freddy	3b1b24c2ce	Update agent/proxycfg/state_test.go	5 years ago
freddygv	eddd5bd73b	PR comments	5 years ago
freddygv	913b13f31f	Add subset support	5 years ago
freddygv	24207226ca	Add proxycfg state management for terminating-gateways	5 years ago
Kyle Havlovitz	e9e8c0e730	Ingress Gateways for TCP services (#7509 ) * Implements a simple, tcp ingress gateway workflow This adds a new type of gateway for allowing Ingress traffic into Connect from external services. Co-authored-by: Chris Piraino <cpiraino@hashicorp.com>	5 years ago
Chris Piraino	584f90bbeb	Fix flapping of mesh gateway connect-service watches (#7575 )	5 years ago
Matt Keeler	9e5fd7f925	OSS Changes for various config entry namespacing bugs (#7226 )	5 years ago
Matt Keeler	dfb0177dbc	Testing updates to support namespaced testing of the agent/xds… (#7185 ) * Various testing updates to support namespaced testing of the agent/xds package * agent/proxycfg package updates to support better namespace testing	5 years ago
Chris Piraino	401221de58	Allow users to configure either unstructured or JSON logging (#7130 ) * hclog Allow users to choose between unstructured and JSON logging	5 years ago
Matt Keeler	c09693e545	Updates to Config Entries and Connect for Namespaces (#7116 )	5 years ago
R.B. Boyer	97aa050c20	agent: allow mesh gateways to initialize even if there are no connect services registered yet (#6576 ) Fixes #6543 Also improved some of the proxycfg tests to cover snapshot validity better.	5 years ago
R.B. Boyer	561b2fe606	connect: generate the full SNI names for discovery targets in the compiler rather than in the xds package (#6340 )	5 years ago
R.B. Boyer	8e22d80e35	connect: fix failover through a mesh gateway to a remote datacenter (#6259 ) Failover is pushed entirely down to the data plane by creating envoy clusters and putting each successive destination in a different load assignment priority band. For example this shows that normally requests go to 1.2.3.4:8080 but when that fails they go to 6.7.8.9:8080: - name: foo load_assignment: cluster_name: foo policy: overprovisioning_factor: 100000 endpoints: - priority: 0 lb_endpoints: - endpoint: address: socket_address: address: 1.2.3.4 port_value: 8080 - priority: 1 lb_endpoints: - endpoint: address: socket_address: address: 6.7.8.9 port_value: 8080 Mesh gateways route requests based solely on the SNI header tacked onto the TLS layer. Envoy currently only lets you configure the outbound SNI header at the cluster layer. If you try to failover through a mesh gateway you ideally would configure the SNI value per endpoint, but that's not possible in envoy today. This PR introduces a simpler way around the problem for now: 1. We identify any target of failover that will use mesh gateway mode local or remote and then further isolate any resolver node in the compiled discovery chain that has a failover destination set to one of those targets. 2. For each of these resolvers we will perform a small measurement of comparative healths of the endpoints that come back from the health API for the set of primary target and serial failover targets. We walk the list of targets in order and if any endpoint is healthy we return that target, otherwise we move on to the next target. 3. The CDS and EDS endpoints both perform the measurements in (2) for the affected resolver nodes. 4. For CDS this measurement selects which TLS SNI field to use for the cluster (note the cluster is always going to be named for the primary target) 5. For EDS this measurement selects which set of endpoints will populate the cluster. Priority tiered failover is ignored. One of the big downsides to this approach to failover is that the failover detection and correction is going to be controlled by consul rather than deferring that entirely to the data plane as with the prior version. This also means that we are bound to only failover using official health signals and cannot make use of data plane signals like outlier detection to affect failover. In this specific scenario the lack of data plane signals is ok because the effectiveness is already muted by the fact that the ultimate destination endpoints will have their data plane signals scrambled when they pass through the mesh gateway wrapper anyway so we're not losing much. Another related fix is that we now use the endpoint health from the underlying service, not the health of the gateway (regardless of failover mode).	5 years ago
R.B. Boyer	c395affc93	connect: expose an API endpoint to compile the discovery chain (#6248 ) In addition to exposing compilation over the API cleaned up the structures that would be exchanged to be cleaner and easier to support and understand. Also removed ability to configure the envoy OverprovisioningFactor.	5 years ago
R.B. Boyer	6393edba53	connect: reconcile how upstream configuration works with discovery chains (#6225 ) * connect: reconcile how upstream configuration works with discovery chains The following upstream config fields for connect sidecars sanely integrate into discovery chain resolution: - Destination Namespace/Datacenter: Compilation occurs locally but using different default values for namespaces and datacenters. The xDS clusters that are created are named as they normally would be. - Mesh Gateway Mode (single upstream): If set this value overrides any value computed for any resolver for the entire discovery chain. The xDS clusters that are created may be named differently (see below). - Mesh Gateway Mode (whole sidecar): If set this value overrides any value computed for any resolver for the entire discovery chain. If this is specifically overridden for a single upstream this value is ignored in that case. The xDS clusters that are created may be named differently (see below). - Protocol (in opaque config): If set this value overrides the value computed when evaluating the entire discovery chain. If the normal chain would be TCP or if this override is set to TCP then the result is that we explicitly disable L7 Routing and Splitting. The xDS clusters that are created may be named differently (see below). - Connect Timeout (in opaque config): If set this value overrides the value for any resolver in the entire discovery chain. The xDS clusters that are created may be named differently (see below). If any of the above overrides affect the actual result of compiling the discovery chain (i.e. "tcp" becomes "grpc" instead of being a no-op override to "tcp") then the relevant parameters are hashed and provided to the xDS layer as a prefix for use in naming the Clusters. This is to ensure that if one Upstream discovery chain has no overrides and tangentially needs a cluster named "api.default.XXX", and another Upstream does have overrides for "api.default.XXX" that they won't cross-pollinate against the operator's wishes. Fixes #6159	5 years ago
R.B. Boyer	e8132b61c0	add test for discovery chain agent cache-type (#6130 )	5 years ago
Matt Keeler	4728329aeb	Various Gateway Fixes (#6093 ) * Ensure the mesh gateway configuration comes back in the api within each upstream * Add a test for the MeshGatewayConfig in the ToAPI functions * Ensure we don’t use gateways for dc local connections * Update the svc kind index for deletions * Replace the proxycfg.state cache with an interface for testing Also start implementing proxycfg state testing. * Update the state tests to verify some gateway watches for upstream-targets of a discovery chain.	5 years ago
Paul Banks	0f27ffd163	Proxy Config Manager (#4729 ) * Proxy Config Manager This component watches for local state changes on the agent and ensures that each service registered locally with Kind == connect-proxy has it's state being actively populated in the cache. This serves two purposes: 1. For the built-in proxy, it ensures that the state needed to accept connections is available in RAM shortly after registration and likely before the proxy actually starts accepting traffic. 2. For (future - next PR) xDS server and other possible future proxies that require _push_ based config discovery, this provides a mechanism to subscribe and be notified about updates to a proxy instance's config including upstream service discovery results. * Address review comments * Better comments; Better delivery of latest snapshot for slow watchers; Embed Config * Comment typos * Add upstream Stringer for funsies	6 years ago

32 Commits (c17baadbf87ac9c601f59ad134648dadf832dd87)